Blog List

Wednesday 20 April 2016

WOOD ART

As a contemporary artistic medium, wood is used in traditional and modern styles, and is an excellent medium for new art. Wood is used in forms of sculpture, craft, and decoration including chip carving, wood burning, and marquetry. Wood offers a fascination, beauty, and complexity in the grain, that often shows even when the medium is painted. Wood is used by carpenters to create many useful items such as cabinets, furniture and musical instruments. Artists use wood for sculpture because it is plentiful and inexpensive when compared to other media like stone or bronze. It is in some ways easier to shape than harder substances, but an artist must develop specific skills to carve it properly. Wood does not last as long as other sculpting media because it can be affected by water rot, dry rot, insect invasion and fire.


In this ebony sculpture, the artist has made use of the contrasting colors and textures in a single piece of wood.

One popular form of wood art production is woodturning. Woodturning on a simple lathe, such as a bow lathe or two-person lathe, primarily for practical purposes has occurred since as early as 1300 B.C. Edward S. Cooke, Jr. points out, "During the economic crises of the 1930s, industrial arts education became more vocational in purpose."  From the 1930s, the field of wood turning grew from this hobbyist movement in the 1930s to fine artists in the 1970s, experimenting with super object forms and other fine craft concepts. At present, there are a variety of international galleries exhibiting wood art, including The Center for Art in Wood in Philadelphia, which houses a museum collection and research library in addition to rotating gallery exhibitions. 

Grain
A person who begins woodcarving is challenged to learn to work with the fiber and grain. Hardness and fragility vary with the species of wood. In general, wood tends to break in the "split direction", the direction in which the fibers separate. In the composition of work, one must work with and around this. Each direction of cut feels and works differently. Sharp tools are essential in allowing the artist's sense to shape the material.
Softwood (common framing stud, endgrain view).
Planks of wood are said to be quarter-sawn when the growth rings are more or less at right angles to the thickness. If the growth rings are more parallel to the width, then the plank is said to be slab-cut. While slab-cut planks are seasoning, they tend to cup in a direction so as to "straighten" the growth rings.
Hardwood (Maple), endgrain view.
Seasoned wood never completely stabilizes, but continues to swell and shrink with seasonal humidity and temperature variations. Any design concept using wood must allow for the particulars of this dimensional variation. Warped wood may be described as bent, twisted, or cupped, or some combination of those modes.
Species

Here are just a few commonly used hardwood and softwood species; many more may be found in List of woods. Each has its own character.

Hardwood

  • Balsa (Ochroma) is technically a hardwood, but is actually softer than most softwoods and very easily shaped. Its most familiar use is in model airplanes.
  • Basswood (Tilia) also known as lime or linden, is a relatively soft, close-grained wood, easily carved.
  • Birch (Betula) is a light-colored, fine-grained wood.
  • Elm (Ulmus) is notorious for its twisting, intertwined grain.
  • Maple (Acer) may be seen in a variety of figures known as curly maple, including tiger-stripe or "fiddleback", bird's-eye and quilted.
  • Oak (Quercus) species are typically dense, hard and show distinctive pores and medullary rays.
  • Walnut (Juglans) is typically dark, hard, tight-grained wood prized for fine furniture and wood paneling.

Softwood

  • Cedar (Cedrus) is fairly hard and aromatic.
  • Fir (Abies) is soft and white.
  • Pine (Pinus) is a fast-growing wood grown commercially for use in construction and paper pulp industries.
  • Spruce (Picea) is used for the soundboards of musical instruments as well as in aviation construction.

Fastening and Joining

See Woodworking joints and Adhesives.

Finishing
The grain and figure of the wood interact with the shape of the piece to make interesting visual and tactile effects. The surface texture may be manipulated by sanding, scraping, scorching, weathering, or leaving it just as it came from the shaping. Processes such as sanding or rasping have one sort of effect, while cutting (planing, chiseling, gouging, or other carving) leaves the surface with a distinctively clear and fresh appearance, particularly if the tool is well-sharpened. Some finishing processes may leave a corduroy effect, where the lines of harder late wood contrast with the often paler, softer, early wood.
Coffee scoop showing tool marks from a Forstner bit.
Each tool used to shape wood usually leaves a signature, or distinctive set of marks. For example, it is easy to tell a cut made by a bandsaw from that of a circular saw. If a smooth surface is desired, then planes, scrapers, or sandpaper are useful for "erasing" toolmarks. Sometimes it is more interesting to leave the tool marks showing. Some centuries-old violin scrolls, for instance, still carry the tool marks of the master that made them, working rapidly and efficiently.
More smoothly finished tea scoop, with carved cicadas.
The texture and appearance of wood grain may be enhanced and preserved by the use of an appropriate coating process, either transparent, such as varnish or opaque, like paint. The finish coats may also help seal the surface, reducing the adverse effects of humidity or sunlight. Other pieces may benefit from the use of unsealed, weathered material such as barn wood or driftwood.
Tools and sharpening

Working with wood, pertains mainly to "cutting away the material that doesn't look like the object in mind." Saws, rasps, chisels, gouges and knives are all useful, and must be well sharpened to work effectively and safely. Dull tools are actually more dangerous than sharp ones; excessive force used on a dull edge can lead to slips and injury.

References

  1. a b Woodturning in North America Since 1930. Wood Turning Center and Yale University Art Gallery. 2001. pp. 15–17; 64. ISBN 0-89467-094-8.
  2. ^ "About | The Center for Art in Wood". centerforartinwood.org. Retrieved 2015-10-13.
  3. ^ http://www.fpl.fs.fed.us/documnts/pdf1983/simps83a.pdf

- Wikipedia 

Mastering Hand Tools

THE JEFF MILLER WOODWORKING COLLECTION - ORDER NOW!

By Christopher Schwarz

Format: Download 

Learn the Benefits of Hand Tools!
In this comprehensive, two-part (nearly four-hours long) video download, Host Christopher Schwarz starts off the video by asking the question, ""Why use Hand Tools?"" A fair question that he quickly answers by extolling the benefits of traditional woodworking tools — blended with some of the niceties of power tools. Those benefits include a healthier work environment, fewer jigs and test cuts, and accuracy to within .001"".
In Mastering Hand Tools, Chris introduces you to the basic hand tool skills to turn you into a woodworker equally comfortable in either the powered or hand tool world — and offer the best results from each world. Watch along as Chris offers advice on selecting hand tools, shares tips for set-up and puts the tools to work.
Learn About:
  • Selecting and using Handsaws and Rasps
  • Sharpening and using Jack planes and Smoothing planes
  • Choosing and using marking knives and gauges and cutting gauges
  • The benefits of Braces and Hand Drills
  • and more about Chisels, Mallets, Scrapers and Router Planes
Christopher Schwarz is the former editor of Popular Woodworking Magazine, and is now a contributing editor to that magazine. He has produced several DVDs for Popular Woodworking and also in conjunction with Lie-Nielsen Toolworks on traditional skills.
 PLEASE NOTE: You will need a broadband connection (or better) to download this video lesson. These video files will only play in the free QuickTime player. Click here to download the QuickTime Player. This video is also available to purchase on DVD. Click here for more information.

For further information log on website:

http://www.shopwoodworking.com/mastering-handtools-dwnld-u6380?source=igodigital

How to Make Homemade Baby Food With Pears

The sweet taste of pears are often well liked by babies and they are nutritious. Pears are high in fiber, a good source of copper and rich in vitamins C and K, according to the George Mateljan Foundation. Prepare your own homemade baby food out of fresh homegrown or store bought pears. Not only will you save money over pre-prepared commercial baby food brands, you can assure your baby's food contains the highest quality and freshest ingredients.
How to Make Homemade Baby Food With Pears

Homemade pear baby food in a bowl. Photo Credit Stitchik/iStock/Getty Images.

Step 1

Scrub cooking utensils and preparation surfaces with soap and hot water to reduce the possibility of contaminating the baby food with germs and bacteria.

Step 2

Wash your hands with soap and warm water to avoid transferring germs and bacteria from your hands to the food.

Step 3

Peel the skin off the pears using a potato peeler and remove the stems. Discard the skins and stems.

Step 4

Cut the pears in half using a paring knife and remove the center cores and seeds. Discard the cores and seeds.
Step 5
Cook the pear halves in a covered small pot filled with 4 teaspoons of water per pear, for three to five minutes or until the pears are easily pierced with a fork. The University of Maine recommends lightly cooking fresh pears before using them in a baby food recipe. Cooked pears are softer so they blend to a finer texture and are easier to digest.

Step 6

Puree the pears and cooking water in a blender until smooth. Add more water, if necessary, to obtain the desired baby food texture. If you do not have a blender, you can push the pears through a fine sieve and stir in in the cooking water.

Step 7

Cool your homemade pear baby food to room temperature before feeding to your baby. Store excess pear baby food in a sealed container in the refrigerator for up to three days. For longer storage, freeze the pear baby food in ice cube containers. Once frozen, toss the frozen pear cubes in a sealed freezer container. Defrost pear cubes in the refrigerator overnight, before feeding them to your baby.
www.livestrong.com

LATHE

lathe /ˈleɪð/ is a machine tool that rotates the workpiece on its axis to perform various operations such as cutting, sanding, knurling, drilling or deformation, facing, turning, with tools that are applied to the workpiece to create an object with symmetry about an axis of rotation.


A metalworking lathe from 1911, showing component parts:
a – bed
b – carriage (with cross-slide and toolpost)
c – headstock
d – back gear (other geartrain nearby drives leadscrew)
e – cone pulley for a belt drive from an external power source
f – faceplate mounted on spindle
g – tailstock
h – leadscrew
Lathes are used in woodturning, metalworking,  metal spinning, thermal spraying, parts reclamation, and glass-working. Lathes can be used to shape pottery the best-known design being the potter's wheel. Most suitably equipped metalworking lathes can also be used to produce most solids of revolution, plane surfaces and screw threads or helices. Ornamental lathes can produce three-dimensional solids of incredible complexity. The workpiece is usually held in place by either one or two centers, at least one of which can typically be moved horizontally to accommodate varying workpiece lengths. Other work-holding methods include clamping the work about the axis of rotation using a chuck or collet or to a faceplate, using clamps or dogs.
A watchmaker using a lathe to prepare a component cut from copper for a watch.
Examples of objects that can be produced on a lathe include candlestick holders, gun barrels, cue sticks, table legs, bowls, baseball bats, musical instruments (especially woodwind instruments), crankshafts, and camshafts.
History
The lathe is an ancient tool, dating at least to ancient Egypt and known to be used in Assyria and ancient Greece. The lathe was very important to the Industrial Revolution.
The origin of turning dates to around 1300 BCE when the Ancient Egyptians first developed a two-person lathe. One person would turn the wood work piece with a rope while the other used a sharp tool to cut shapes in the wood. Ancient Rome improved the Egyptian design with the addition of a turning bow. In the Middle Ages a pedal replaced hand-operated turning, allowing a single person to rotate the piece while working with both hands. The pedal was usually connected to a pole, often a straight-grained sapling. The system today is called the "spring pole" lathe. Spring pole lathes were in common use into the early 20th century.
An important early lathe in the UK was the horizontal boring machine that was installed in 1772 in the Royal Arsenal in Woolwich. It was horse-powered and allowed for the production of much more accurate and stronger cannon used with success in the American Revolutionary War in the late 18th century. One of the key characteristics of this machine was that the workpiece was turning as opposed to the tool, making it technically a lathe (see attached drawing). Henry Maudslay who later developed many improvements to the lathe worked at the Royal Arsenal from 1783 being exposed to this machine in the Verbruggen workshop.
Exact drawing made with camera obscura of horizontal boring machine by Jan Verbruggen in Woolwich Royal Brass Foundry approx 1778 (drawing 47 out of set of 50 drawings)
During the Industrial Revolution, mechanized power generated by water wheels or steam engines was transmitted to the lathe via line shafting, allowing faster and easier work. Metalworking lathes evolved into heavier machines with thicker, more rigid parts. Between the late 19th and mid-20th centuries, individual electric motors at each lathe replaced line shafting as the power source. Beginning in the 1950s, servomechanisms were applied to the control of lathes and other machine tools via numerical control, which often was coupled with computers to yield computerized numerical control (CNC). Today manually controlled and CNC lathes coexist in the manufacturing industries.
Description
Parts
A lathe may or may not have legs, which sit on the floor and elevate the lathe bed to a working height. A lathe may be small and sit on a workbench or table, not requiring a stand.
Almost all lathes have a bed, which is (almost always) a horizontal beam (although CNC lathes commonly have an inclined or vertical beam for a bed to ensure that swarf, or chips, falls free of the bed). Woodturning lathes specialized for turning large bowls often have no bed or tail stock, merely a free-standing headstock and a cantilevered tool rest.
At one end of the bed (almost always the left, as the operator faces the lathe) is a headstock. The headstock contains high-precision spinning bearings. Rotating within the bearings is a horizontal axle, with an axis parallel to the bed, called the spindle. Spindles are often hollow and have exterior threads and/or an interior Morse taper on the "inboard" (i.e., facing to the right / towards the bed) by which work-holding accessories may be mounted to the spindle. Spindles may also have exterior threads and/or an interior taper at their "outboard" (i.e., facing away from the bed) end, and/or may have a hand-wheel or other accessory mechanism on their outboard end. Spindles are powered and impart motion to the workpiece.
The spindle is driven either by foot power from a treadle and flywheel or by a belt or gear drive to a power source. In most modern lathes this power source is an integral electric motor, often either in the headstock, to the left of the headstock, or beneath the headstock, concealed in the stand.
In addition to the spindle and its bearings, the headstock often contains parts to convert the motor speed into various spindle speeds. Various types of speed-changing mechanism achieve this, from a cone pulley or step pulley, to a cone pulley with back gear (which is essentially a low range, similar in net effect to the two-speed rear of a truck), to an entire gear train similar to that of a manual-shift auto transmission. Some motors have electronic rheostat-type speed controls, which obviates cone pulleys or gears.
The counterpoint to the headstock is the tailstock, sometimes referred to as the loose head, as it can be positioned at any convenient point on the bed by sliding it to the required area. The tail-stock contains a barrel, which does not rotate, but can slide in and out parallel to the axis of the bed and directly in line with the headstock spindle. The barrel is hollow and usually contains a taper to facilitate the gripping of various types of tooling. Its most common uses are to hold a hardened steel center, which is used to support long thin shafts while turning, or to hold drill bits for drilling axial holes in the work piece. Many other uses are possible.
Metalworking lathes have a carriage (comprising a saddle and apron) topped with a cross-slide, which is a flat piece that sits crosswise on the bed and can be cranked at right angles to the bed. Sitting atop the cross slide is usually another slide called a compound rest, which provides 2 additional axes of motion, rotary and linear. Atop that sits a toolpost, which holds a cutting tool, which removes material from the workpiece. There may or may not be a leadscrew, which moves the cross-slide along the bed.
Woodturning and metal spinning lathes do not have cross-slides, but rather have banjos, which are flat pieces that sit crosswise on the bed. The position of a banjo can be adjusted by hand; no gearing is involved. Ascending vertically from the banjo is a tool-post, at the top of which is a horizontal toolrest. In woodturning, hand tools are braced against the tool rest and levered into the workpiece. In metal spinning, the further pin ascends vertically from the tool rest and serves as a fulcrum against which tools may be levered into the workpiece.
Accessories
Unless a workpiece has a taper machined onto it which perfectly matches the internal taper in the spindle, or has threads which perfectly match the external threads on the spindle (two conditions which rarely exist), an accessory must be used to mount a workpiece to the spindle.
A workpiece may be bolted or screwed to a faceplate, a large, flat disk that mounts to the spindle. In the alternative, faceplate dogs may be used to secure the work to the faceplate.
A steady rest.
A workpiece may be mounted on a mandrel or circular work clamped in a three- or four-jaw chuck. For irregular shaped workpieces it is usual to use a four jaw (independent moving jaws) chuck. These holding devices mount directly to the Lathe headstock spindle.
In precision work, and in some classes of repetition work, cylindrical workpieces are usually held in a collet inserted into the spindle and secured either by a draw-bar, or by a collet closing cap on the spindle. Suitable collets may also be used to mount square or hexagonal workpieces. In precision toolmaking work such collets are usually of the draw-in variety, where, as the collet is tightened, the workpiece moves slightly back into the headstock, whereas for most repetition work the dead length variety is preferred, as this ensures that the position of the workpiece does not move as the collet is tightened.
A soft workpiece (e.g., wood) may be pinched between centers by using a spur drive at the headstock, which bites into the wood and imparts torque to it.
A soft dead center is used in the headstock spindle as the work rotates with the centre. Because the centre is soft it can be trued in place before use. The included angle is 60°. Traditionally, a hard dead center is used together with suitable lubricant in the tailstock to support the workpiece. In modern practice the dead center is frequently replaced by a live center, as it turns freely with the workpiece — usually on ball bearings — reducing the frictional heat, especially important at high speeds. When clear facing a long length of material it must be supported at both ends. This can be achieved by the use of a traveling or fixed steady. If a steady is not available, the end face being worked on may be supported by a dead (stationary) half center. A half center has a flat surface machined across a broad section of half of its diameter at the pointed end. A small section of the tip of the dead center is retained to ensure concentricity. Lubrication must be applied at this point of contact and tail stock pressure reduced. A lathe carrier or lathe dog, may also be employed when turning between two centers.
Live center (top); dead center (bottom).
In woodturning, one variation of a live center is a cup center, which is a cone of metal surrounded by an annular ring of metal that decreases the chances of the workpiece splitting.
A circular metal plate with even spaced holes around the periphery, mounted to the spindle, is called an "index plate". It can be used to rotate the spindle to a precise angle, then lock it in place, facilitating repeated auxiliary operations done to the workpiece.
Other accessories, including items such as taper turning attachments, knurling tools, vertical slides, fixed and traveling steadies, etc., increase the versatility of a lathe and the range of work it may perform.
Modes of use
When a workpiece is fixed between the headstock and the tail-stock, it is said to be "between centers". When a workpiece is supported at both ends, it is more stable, and more force may be applied to the workpiece, via tools, at a right angle to the axis of rotation, without fear that the workpiece may break loose.
When a workpiece is fixed only to the spindle at the headstock end, the work is said to be "face work". When a workpiece is supported in this manner, less force may be applied to the workpiece, via tools, at a right angle to the axis of rotation, lest the workpiece rip free. Thus, most work must be done axially, towards the headstock, or at right angles, but gently.
When a workpiece is mounted with a certain axis of rotation, worked, then remounted with a new axis of rotation, this is referred to as "eccentric turning" or "multi-axis turning". The result is that various cross sections of the workpiece are rotationally symmetric, but the workpiece as a whole is not rotationally symmetric. This technique is used for camshafts, various types of chair legs.
Varieties

The smallest lathes are "jewelers lathes" or "watchmaker lathes", which are small enough that they may be held in one hand. The workpieces machined on a jeweler's lathe are metal. Jeweler's lathes can be used with hand-held "graver" tools or with compound rests that attach to the lathe bed. Graver tools are generally supported by a T-rest, not fixed to a cross slide or compound rest. The work is usually held in a collet. Common spindle bore sizes are 6 mm, 8 mm and 10 mm. The term W/W refers to the Webster/Whitcomb collet and lathe, invented by the American Watch Tool Company of Waltham, Massachusetts. Most lathes commonly referred to as watchmakers lathes are of this design. In 1909, the American Watch Tool company introduced the Magnus type collet (a 10-mm body size collet) using a lathe of the same basic design, the Webster/Whitcomb Magnus. (F.W.Derbyshire, Inc. retains the trade names Webster/Whitcomb and Magnus and still produces these collets.) Two bed patterns are common: the WW (Webster Whitcomb) bed, a truncated triangular prism (found only on 8 and 10 mm watchmakers' lathes); and the continental D-style bar bed (used on both 6 mm and 8 mm lathes by firms such as Lorch and Star). Other bed designs have been used, such a triangular prism on some Boley 6.5 mm lathes, and a V-edged bed on IME's 8 mm lathes.


Smaller metalworking lathes that are larger than jewelers' lathes and can sit on a bench or table, but offer such features as tool holders and a screw-cutting gear train are called hobby lathes, and larger versions, "bench lathes". Even larger lathes offering similar features for producing or modifying individual parts are called "engine lathes". Lathes of these types do not have additional integral features for repetitive production, but rather are used for individual part production or modification as the primary role.
Lathes of this size that are designed for mass manufacture, but not offering the versatile screw-cutting capabilities of the engine or bench lathe, are referred to as "second operation" lathes.
Lathes with a very large spindle bore and a chuck on both ends of the spindle are called "oil field lathes".
Fully automatic mechanical lathes, employing cams and gear trains for controlled movement, are called screw machines.
Lathes that are controlled by a computer are CNC lathes.
Lathes with the spindle mounted in a vertical configuration, instead of horizontal configuration, are called vertical lathes or vertical boring machines. They are used where very large diameters must be turned, and the workpiece (comparatively) is not very long.
A lathe with a cylindrical tail-stock that can rotate around a vertical axis, so as to present different tools towards the headstock (and the workpiece) are turret lathes.
A lathe equipped with indexing plates, profile cutters, spiral or helical guides, etc., so as to enable ornamental turning is an ornamental lathe.
Various combinations are possible: for example, a vertical lathe can have CNC capabilities as well (such as a CNC VTL).
Lathes can be combined with other machine tools, such as a drill press or vertical milling machine. These are usually referred to as combination lathes.
Major categories
Woodworking lathes
Woodworking lathes are the oldest variety. All other varieties are descended from these simple lathes. An adjustable horizontal metal rail – the tool rest – between the material and the operator accommodates the positioning of shaping tools, which are usually hand-held. After shaping, it is common practice to press and slide sandpaper against the still-spinning object to smooth the surface made with the metal shaping tools. The tool rest is usually removed during sanding, as it may be unsafe to have the operators hands between it and the spinning wood.
Many woodworking lathes can also be used for making bowls and plates. The bowl or plate needs only to be held at the bottom by one side of the lathe. It is usually attached to a metal face plate attached to the spindle. With many lathes, this operation happens on the left side of the headstock, where are no rails and therefore more clearance. In this configuration, the piece can be shaped inside and out. A specific curved tool rest may be used to support tools while shaping the inside. Further detail can be found on the woodturning page.
A modern woodworking lathe.
Most woodworking lathes are designed to be operated at a speed of between 200 and 1,400 revolutions per minute, with slightly over 1,000 rpm considered optimal for most such work, and with larger workpieces requiring lower speeds.
Patternmaker lathes

Used to make a pattern for foundries often from wood, but also plastics. A patternmaker's lathe looks like a heavy wood lathe, often with a turret and either a leadscre or a rack and pinion to manually position the turret. The turret is used to accurately cut straight lines. They often have a provision to turn very large parts on the other end of the headstock, using a free-standing toolrest. Another way of turning large parts is a sliding bed, which can slide away from the headstock and thus open up a gap in front of the headstock for large parts.


Patternmaker's double lathe (Carpentry and Joinery, 1925).

Metal workings lathes
In a metalworking lathe, metal is removed from the workpiece using a hardened cutting tool, which is usually fixed to a solid moveable mounting, either a tool-post or a turret, which is then moved against the workpiece using handwheels and/or computer-controlled motors. These cutting tools come in a wide range of sizes and shapes, depending upon their application. Some common styles are diamond, round, square and triangular.
The tool-post is operated by lead-screws that can accurately position the tool in a variety of planes. The tool-post may be driven manually or automatically to produce the roughing and finishing cuts required to turn the workpiece to the desired shape and dimensions, or for cutting threads, worm gears, etc. Cutting fluid may also be pumped to the cutting site to provide cooling, lubrication and clearing of swarf from the workpiece. Some lathes may be operated under control of a computer for mass production of parts (see "Computer numerical control").
A CNC metalworking lathe.
Manually controlled metalworking lathes are commonly provided with a variable-ratio gear-train to drive the main lead-screw. This enables different thread pitches to be cut. On some older lathes or more affordable new lathes, the gear trains are changed by swapping gears with various numbers of teeth onto or off of the shafts, while more modern or expensive manually controlled lathes have a quick-change box to provide commonly used ratios by the operation of a lever. CNC lathes use computers and servomechanisms to regulate the rates of movement.
On manually controlled lathes, the thread pitches that can be cut are, in some ways, determined by the pitch of the lead-screw: A lathe with a metric lead-screw will readily cut metric threads (including BA), while one with an imperial lead-screw will readily cut imperial-unit-based threads such as BSW or UTS (UNF, UNC). This limitation is not insurmountable, because a 127-tooth gear, called a transposing gear, is used to translate between metric and inch thread pitches. However, this is optional equipment that many lathe owners do not own. It is also a larger change-wheel than the others, and on some lathes may be larger than the change-wheel mounting banjo is capable of mounting.
The workpiece may be supported between a pair of points called centres, or it may be bolted to a faceplate or held in a chuck. A chuck has movable jaws that can grip the workpiece securely.
There are some effects on material properties when using a metalworking lathe. There are few chemical or physical effects, but there are many mechanical effects, which include residual stress, micro-cracks, work-hardening, and tempering in hardened materials.
Cue lathes

Cue lathes function similarly to turning and spinning lathes, allowing a perfectly radially-symmetrical cut for billiard cues. They can also be used to refinish cues that have been worn over the years.

Glass-working lathes
Glass-working lathes are similar in design to other lathes, but differ markedly in how the workpiece is modified. Glass-working lathes slowly rotate a hollow glass vessel over a fixed- or variable-temperature flame. The source of the flame may be either hand-held or mounted to a banjo/cross-slide that can be moved along the lathe bed. The flame serves to soften the glass being worked, so that the glass in a specific area of the workpiece becomes ductile and subject to forming either by inflation ("glassblowing") or by deformation with a heat-resistant tool. Such lathes usually have two head-stocks with chucks holding the work, arranged so that they both rotate together in unison. Air can be introduced through the headstock chuck spindle for glassblowing. The tools to deform the glass and tubes to blow (inflate) the glass are usually handheld.
In diamond turning, a computer-controlled lathe with a diamond-tipped tool is used to make precision optical surfaces in glass or other optical materials. Unlike conventional optical grinding, complex aspheric surfaces can be machined easily. Instead of the dovetailed ways used on the tool slide of a metal-turning lathe, the ways typically float on air bearings, and the position of the tool is measured by optical interferometry to achieve the necessary standard of precision for optical work. The finished work piece usually requires a small amount of subsequent polishing by conventional techniques to achieve a finished surface suitably smooth for use in a lens, but the rough grinding time is significantly reduced for complex lenses.
Metal-spinning lathes
In metal spinning, a disk of sheet metal is held perpendicularly to the main axis of the lathe, and tools with polished tips (spoons) or roller tips are hand-held, but levered by hand against fixed posts, to develop pressure that deforms the spinning sheet of metal.
Metal-spinning lathes are almost as simple as wood-turning lathes. Typically, metal spinning requires a mandrel, usually made from wood, which serves as the template onto which the workpiece is formed (asymmetric shapes can be made, but it is a very advanced technique). For example, to make a sheet metal bowl, a solid block of wood in the shape of the bowl is required; similarly, to make a vase, a solid template of the vase is required.
Given the advent of high-speed, high-pressure, industrial die forming, metal spinning is less common now than it once was, but still a valuable technique for producing one-off prototypes or small batches, where die forming would be uneconomical.
Ornamental turning lathes
The ornamental turning lathe was developed around the same time as the industrial screw-cutting lathe in the nineteenth century. It was used not for making practical objects, but for decorative, work – ornamental turning. By using accessories such as the horizontal and vertical cutting frames, eccentric chuck and elliptical chuck, solids of extraordinary complexity may be produced by various generative procedures.
A special-purpose lathe, the Rose engine lathe, is also used for ornamental turning, in particular for engine turning, typically in precious metals, for example to decorate pocket-watch cases. As well as a wide range of accessories, these lathes usually have complex dividing arrangements to allow the exact rotation of the mandrel. Cutting is usually carried out by rotating cutters, rather than directly by the rotation of the work itself. Because of the difficulty of polishing such work, the materials turned, such as wood or ivory, are usually quite soft, and the cutter has to be exceptionally sharp. The finest ornamental lathes are generally considered to be those made by Holtzapffel around the turn of the 19th century.
Reducing lathe
Many types of lathes can be equipped with accessory components to allow them to reproduce an item: the original item is mounted on one spindle, the blank is mounted on another, and as both turn in synchronized manner, one end of an arm "reads" the original and the other end of the arm "carves" the duplicate.
reduction lathe is a specialized lathe that is designed with this feature and incorporates a mechanism similar to a pantograph, so that when the "reading" end of the arm reads a detail that measures one inch (for example), the cutting end of the arm creates an analogous detail that is (for example) one quarter of an inch (a 4:1 reduction, although given appropriate machinery and appropriate settings, any reduction ratio is possible).
Reducing lathes are used in coin-making, where a plaster original (or an epoxy master made from the plaster original, or a copper-shelled master made from the plaster original, etc.) is duplicated and reduced on the reducing lathe, generating a master die.
Rotary lathes

A lathe in which softwood, like spruce or pine, or hardwood, like birch, logs are turned against a very sharp blade and peeled off in one continuous or semi-continuous roll. Invented by Immanuel Nobel (father of the more famous Alfred Nobel). The first such lathes were set up in the United States in the mid-19th century. The product is called wood veneer and it is used for making plywood and as a cosmetic surface veneer on some grades of chipboard.

Watch maker lathes

Watchmakers lathes are delicate but precise metalworking lathes, usually without provision for screwcutting, and are still used by horologists for work such as the turning of balance staffs. A handheld tool called a graver is often used in preference to a slide-mounted tool. The original watchmaker's turns was a simple dead-center lathe with a moveable rest and two loose head-stocks. The workpiece would be rotated by a bow, typically of horsehair, wrapped around it.

Transcriptions or recording lathes

Transcription, or recording, lathes are used to make grooves on a surface for recording sounds. These were used in creating sound grooves on wax cylinders and then on flat recording discs. Originally the cutting lathes were driven by sound vibrations through a horn and then later driven by electric current, when microphones were used in recording. Many of these were professional models, but there were some used for home recording and were popular before the advent of home tape recording.

Gallery
Example of lathes

Example of work produced from a lathe

Lathe exercise.
Performers evaluation

National and international standards are used to standardize the definitions, environmental requirements, and test methods used for the performance evaluation of lathes. Selection of the standard to be used is an agreement between the supplier and the user and has some significance in the design of the lathe. In the United States, ASME has developed the B5.57 Standard entitled "Methods for Performance Evaluation of Computer Numerically Controlled Lathes and Turning Centers", which establishes requirements and methods for specifying and testing the performance of CNC lathes and turning centers. 

References

  1. ^ presentation by Tetsuo Tomiyama of Technical University Delft on the development of production technology including the Verbruggen Lathe.
  2. ^ Inthewoodshop.org.
  3. ^ "Hints & Tips for Using a Lathe". “George Wilson’s” Hints and Tips - Publication date unknown. Lathes.co.uk. Retrieved 29 November 2010.
  4. ^ Parker, Dana T. Building Victory: Aircraft Manufacturing in the Los Angeles Area in World War II, p. 81, 123, Cypress, CA, 2013. ISBN 978-0-9897906-0-4.
  5. ^ Ernie Conover (2000), Turn a Bowl with Ernie Conover: Getting Great Results the First Time Around, Taunton, p. 16, ISBN 978-1-56158-2938.
  6. ^ https://www.asme.org/products/codes-standards/b557-2012-methods-performance-evaluation-computer.

Further Reading

  • Holtzapffel, Charles (1843–1897). Turning and Mechanical Manipulation Volume V.
  • Marlow, Frank (2008). Machine Shop Essentials: Q & A. Metal Arts Press. ISBN 978-0-9759963-3-1.
  • Oscar E. Perrigo. Modern American Lathe Practice. A New, Complete and Practical Work on the "king of Machine Shop Tools" , 1907.
  • Raffan, Richard (2001). Turning Wood With Richard Raffan. Taunton. ISBN 1-56158-417-7.
  • Joshua Rose.  The Complete Practical Machinist: Embracing Lathe Work, Vise Work, Drills, etc,  Philadelphia: H.C. Baird & Co., 1876; 2nd ed. 1885.
  • Sparey, Lawrence (1947). The Amateur's Lathe. Special Interest Model Books. ISBN 0-85242-288-1.
  • Woodbury, Robert S, (1961). History of the Lathe to 1850. Cleveland, Ohio: Society for the History of Technology. ISBN 978-0-262-73004-4.
External


- Wikipedia 

Advantages and Disadvantages of Fasting for Runners

Author BY   ANDREA CESPEDES  Food is fuel, especially for serious runners who need a lot of energy. It may seem counterintuiti...