BANDSAW

A bandsaw is a power tool which uses a blade consisting of a continuous band of metal with teeth along one edge to cut various workpieces. The band usually rides on two wheels rotating in the same plane, although some bandsaws may have three or four wheels. Bandsawing produces uniform cutting action as a result of an evenly distributed tooth load. Bandsaws are used for woodworking, metalworking, or for cutting a variety of other materials. They are particularly useful for cutting irregular or curved shapes, but can make straight cuts. The minimum radius of a curve that can be cut on a particular saw is determined by the width of the band and its kerf.

A bandsaw in use

A bandsaw on display in a hardware store.

History

The idea of the band saw dates back to at least 1809, when William Newberry received a British patent for the idea, but band saws remained impractical largely because of the blades. Constant flexing of the band saw blade over the band saw wheels caused the material or the welded joint of the blade to fail.

Small boatyard horizontal bandsaw, resaw, Hoi AN, Vietnam.

Nearly 40 years passed before a French woman, Anne Paulin Crepin, devised a technique for welding a band saw blade so that it could withstand the rigors of sawing and bending around band saw wheels. She applied for a patent in 1846, and soon afterward, manufacturer A. Perin & Company of Paris, France, purchased the rights to her innovation. Combining Crepin’s welding method with new steel alloys and advanced tempering techniques, Perin created the first modern band saw blade.

The first American band saw patent was granted to Benjamin Barker of Ellsworth, Maine, in January of 1836.

Larger resaw, Mekong delta boatyard, note width of blades, about 150 mm or 6".

According to the sources the first factory produced and commercially available band saw was the Paul Prybil's band saw patent for cutting wood.

Power hacksaws (with reciprocating blades) were once common in the metalworking industries, but bandsaws and cold saws have mostly displaced them.

Historical bandsaw from 1911.

Types
Meat cutting

Saws for cutting meat are typically of all stainless steel construction with easy to clean features. The blades either have fine teeth with heat treated tips, or have plain or scalloped knife edges.

Metal cutting

Bandsaws for cutting metal are available in vertical and horizontal designs. Typical band speeds range from 40 feet (12 meters) per minute to 5,000 feet (1,500 meters) per minute, however specialized bandsaws are built for friction cutting of hard metals and run band speeds to 15,000 feet per minute. Metal-cutting bandsaws are usually equipped with brushes or brushwheels to prevent chips from becoming stuck in between the blade's teeth. Systems which cool the blade are also common equipment on metal-cutting bandsaws. The coolant washes away chips and keeps the blade cool and lubricated.

19th century wood bandsaw.

Horizontal bandsaws hold the workpiece stationary while the blade swings down through the cut. This configuration is used to cut long materials such as pipe or bar stock to length. Thus it is an important part of the facilities in most machine shops. The horizontal design is not useful for cutting curves or complicated shapes. Small horizontal bandsaws typically employ a gravity feed alone, retarded to an adjustable degree by a coil spring; on industrial models, the rate of descent is usually controlled by a hydraulic cylinder bleeding through an adjustable valve. When the saw is set up for a cut, the operator raises the saw, positions the material to be cut underneath the blade, and then turns on the saw. The blade slowly descends into the material, cutting it as the band blade moves. When the cut is complete, a switch is tripped and the saw automatically turns off. More sophisticated versions of this type of saw are partially or entirely automated (via PLC or CNC)  for high-volume cutting of machining blanks. Such machines provide a stream of cutting fluid recirculated from a sump, in the same manner that a CNC machining center does.

A vertical bandsaw, also called a contour saw, keeps the blade's path stationary while the workpiece is moved across it. This type of saw can be used to cut out complex shapes and angles. The part may be fed into the blade manually or with a power assist mechanism. This type of metal-cutting bandsaw is often equipped with a built-in blade welder. This not only allows the operator to repair broken blades or fabricate new blades quickly, but also allows for the blade to be purposely cut, routed through the center of a part, and re-welded in order to make interior cuts. These saws are often fitted with a built-in air blower to cool the blade and to blow chips away from the cut area giving the operator a clear view of the work. This type of saw is also built in a woodworking version. The woodworking type is generally of much lighter construction and does not incorporate a power feed mechanism, coolant, or welder.

Advancements have also been made in the bandsaw blades used to cut metals. The development of new tooth geometries and tooth pitches have produced increased production rates and greater blade life. New materials and processes such as M51 steel and the cryogenic treatment of blades have produced results that were thought impossible just a few years ago. New machines have been developed to automate the welding process of bandsaw blades as well. Ideal computerized welding machines, setting and cut to length machines and contributions from other manufacturers continue to increase productivity.

Timber cutting

Timber mills use very large bandsaws for ripping lumber; they are preferred over circular saws for ripping because they can accommodate large-diameter timber and because of their smaller kerf (cut size), resulting in less waste.

The blades are mounted on wheels with a diameter large enough not to cause metal fatigue due to flexing when the blade repeatedly changes from a circular to a straight profile. It is stretched very tight (with fatigue strength of the saw metal being the limiting factor). Bandsaws of this size need to have a deformation worked into them that counteracts the forces and heating of operation. This is called benching. They also need to be removed and serviced at regular intervals. Sawfilersor sawdoctors are the craftsmen responsible for this work.

The shape of the tooth gullet is highly optimized and designed by the sawyer and sawfiler. It varies according to the mill, as well as the type and condition of the wood. Frozen logs often require a frost notch ground into the gullet to break the chips. The shape of the tooth gullet is created when the blade is manufactured and its shape is automatically maintained with each sharpening. The sawfiler will need to maintain the grinding wheel's profile with periodic dressing of the wheel.

Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two bandwheels or flywheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, (see Crowned Pulleys) a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth.

Resaws

A resaw is a large bandsaw optimized for cutting timber along the grain to reduce larger sections into smaller sections or veneers. Resawing veneers requires a wide blade—commonly 2 to 3 in (51 to 76 mm)—with a small kerf to minimize waste. Resaw blades of up to 1 in (25 mm) may be fitted to a standard bandsaw.

Double cut sawsEdit

Double cut saws have cutting teeth on both sides. They are generally very large, similar in size to a head saw.

Construction
Feed Mechanism

• Gravity feed saws fall under their own weight. Most such saws have a method to allow the cutting force to be adjusted, such as a movable counterbalancing weight, a coil spring with a screw-thread adjustment, or a hydraulic or pneumatic damper (speed control valve). The latter does not force the blade downwards, but rather simply limits the speed at which the saw can fall, preventing excessive feed on thin or soft parts. This is analogous to door closer hardware whose dampering action keeps the door from slamming. Gravity feed designs are common in small saws.
• Hydraulic feed saws use a positive pressure hydraulic piston to advance the saw through the work at variable pressure and rate. Common in production saws.
• Screw feed saws employ a leadscrew to move the saw.

Fall mechanismsEdit

• Pivot saws hinge in an arc as they advance through the work.
• Single column saws have a large diameter column that the entire saw rides up and down on, very similar to a drill press.
• Dual column saws have a pair of large columns, one on either side of the work, for very high rigidity and precision. The dual column setup is unable to make use of a miter base due to inherent design. Dual column saws are the largest variety of machine bandsaws encountered, to the point where some make use of a rotary table and X axis to perform complex cutting.

Automated Saws

Automatic bandsaws feature preset feed rate, return, fall, part feeding, and part clamping. These are used in production environments where having a machine operator per saw is not practical. One operator can feed and unload many automatic saws.

Some automatic saws rely on numerical control to not only cut faster, but to be more precise and perform more complex miter cuts.

Common tooth formsEdit

• Precision blade gives accurate cuts with a smooth finish.
• Buttress blade provides faster cutting and large chip loads.
• Claw tooth blade gives additional clearance for fast cuts and soft material.

At least two teeth must be in contact with the workpiece at all times to avoid stripping off the teeth.

References

1. ^ Todd, Allen & Alting 1994,  p. 14.
2. ^ Joslin, Jeff. "Pre History of Band Saws".  Retrieved 27 June 2013.
3. ^ Johnson, Roland (2010). Complete Illustrated guide to band saws (PDF). the Taunton Press. p. 6. ISBN 978-1-60085-096-7.
4. ^ Barker, Benjamin. "Band Saw Mill". Patent. Directory of American Tool and Machinery Patents. Retrieved 27 June 2013.
5. ^ Pryibil, Paul. "Improvement in band sawing machines". Patent. Directory of American Tool and Machinery Patents. Retrieved 27 June 2013.
6. ^ Todd, Allen & Alting 1994, p. 15.

Bibliography

• Todd, Robert H.; Allen, Dell K.; Alting, Leo (1994), Manufacturing Processes Reference Guide, Industrial Press Inc., ISBN 0-8311-3049-0.

Further Reading

• Duginske, Mark (1989). The Bandsaw Handbook. Sterling Publishing. ISBN 0-8069-6398-0.

- Wikipedia