Examples of characteristics of wood that affect mould growth: a meta-analysis

Published Date
Original

First Online: 

15 November 2016

DOI: 10.1007/s00107-016-1127-x

Cite this article as: 

Johansson, P., Mjörnell, K. & Arfvidsson, J. Eur. J. Wood Prod. (2016). doi:10.1007/s00107-016-1127-x

Author

• Pernilla JohanssonEmail author
• Kristina Mjörnell
• Jesper Arfvidsson

Abstract

Building materials differ in their susceptibility to mould growth. Wood is a material often considered to have a low mould resistance. However, wood is not a homogenous material and different characteristics of the material are expected to have an impact on mould growth. In this paper, it was shown that wood species (pine or spruce), sawing pattern (centre-board or side-board) and surface structure (planed or sawn) affected mould growth. In addition, it was indicated that the susceptibility cannot be described by one single parameter, but also depends on other parameters. It is therefore difficult to estimate the susceptibility of wood in general. These conclusions were drawn from a meta-analysis, using data from five separate, previously performed laboratory studies conducted at 90% relative humidity and 22 °C, and from a laboratory study performed at 95% RH and 22 °C.

References 

1. Bewick V, Cheek L, Ball J (2004) Statistics review 12: survival analysis. Crit care 8(5):389–394CrossRefPubMedPubMedCentralGoogle Scholar
2. Blackburn C (2000) Modelling shelf-life. In: Kilcast D, Subramaniam P (eds) The stability and shelf-life of food. Woodhead Publishing Limited, CambridgeGoogle Scholar
3. EA-4/02M (2013) Expressions of the uncertainty of measurements in calibration. European Co-operation for Accreditation
4. Hyvärinen A, Meklin T, Vepsäläinen A, Nevalainen A (2002) Fungi and actinobacteria in moisture-damaged building materials—concentrations and diversity. Int Biodeterior Biodegrad 49:27–37CrossRefGoogle Scholar
5. Johansson P (2012) Determination of the critical moisture level for mould growth on building materials. Doctoral thesis. Report TVBH-1020. Lund University
6. Johansson P (2014) Determination of the critical moisture level for mould growth on building materials. Doctoral Thesis. Rapport TVBH-1020. Lund University, Building Physics
7. Johansson P, Bok G (2011) Mould growth on building timber collected from three different single-house factories. SP Rapport 2011:51. SP Technical Research Institute of Sweden
8. Johansson P, Bok G (2014) Mould growth on building timber collected from three different single-house factories. In: 10th Nordic symposium on building physics, Lund, Sweden, 15–19 June 2014
9. Johansson P, Ekstrand-Tobin A (2014) The effect of surface roughness on mould growth on wood. In: 10th Nordic symposium on building physics, Lund, Sweden, 15–19 June 2014
10. Johansson P, Jermer J (2010) Mould growth on wood-based materials—a comparative study. IRG 41 Annual Meeting Biarritz, France
11. Johansson P, Ekstrand-Tobin A, Svensson T, Bok G (2012) Laboratory study to determine the critical moisture level for mould growth on building materials. Int Biodeterior Biodegrad 73:23–32CrossRefGoogle Scholar
12. Johansson P, Bok G, Ekstrand-Tobin A (2013a) The effect of cyclic moisture and temperature on mould growth on wood compared to steady state conditions. Build Environ 65:178–184CrossRefGoogle Scholar
13. Johansson P, Wamming T, Bok G, Edlund M-L (2013b) Mould growth on kiln-dried and air-dried timber. Eur J Wood Prod 71(4):473CrossRefGoogle Scholar
14. Nielsen K F (2002) Mould growth on building materials—secondary metabolites, mycotoxins and biomarkers. By og Byg Statens Byggeforskningsinstitut, Technical University of Denmark
15. Pietarinen VM, Rintala H, Hyvarinen A, Lignell U, Karkkainen P, Nevalainen A (2008) Quantitative PCR analysis of fungi and bacteria in building materials and comparison to culture-based analysis. J Environ Monit 10(5):655–663CrossRefPubMedGoogle Scholar
16. Rich JT, Neely JG, Paniello RC, Voelker CCJ, Nussenbaum B, Wang EW (2010) A practical guide to understanding Kaplan–Meier curves. Otolaryngol Head Neck Surg 143(3):331–336CrossRefPubMedPubMedCentralGoogle Scholar
17. Sehlstedt-Persson M, Karlsson O, Wamming T, Morèn T (2011) Mold growth on sapwood boards exposed outdoors: the impact of wood drying. Forest Prod J 61(2):170–179CrossRefGoogle Scholar
18. Singer JD, Willett JB (2003) Applied longitudinal data analysis: modeling change and event occurrence. Oxford University Press, Oxford, New YorkCrossRefGoogle Scholar
19. SIS-EN Standard 1611-1 (2000) Sawn timber—appearance grading of softwoods—Part 1: European spruces, firs, pines and Douglas firs. Swedish Standards Institute, Stockholm
20. Terziev N, Boutelje J (1998) Effect of felling time and kiln-drying on color and susceptibility of wood to mold and fungal stain during above-ground field test. Wood Fiber Sci 30(4):360–367Google Scholar
21. Terziev N, Bjurman J, Boutelje J (1996) Effect of planing on mould susceptibility of kiln- and air-dried Scots pine (Pinus silvestris L.) lumber. Mat u Org 30(2): 95–103
22. Viitanen H (1996) Factors affecting the development of mould and brown rot decay in wooden material and wooden structures. Effect of humidity, temperature and exposure time. Department of Forest Products. Uppsala, The Swedish University of Agricultural Sciences
23. Viitanen H, Ritschkoff A-C (1991) Mould growth in pine and spruce sapwood in relation to air humidity and temperature. Sweedish University of Agrucultural Sciences, Department of Forest Products, UppsalaGoogle Scholar

For further details log on website :
http://link.springer.com/article/10.1007/s00107-016-1127-x